Tag: calibration

Review of Epson R2880 & ColourMunki Calibration System

I am often asked what printer I use. Until a few months ago the answer was, ‘I don’t use a printer’. ( I do have a HP desk top printer but it is only suitable for document printing ). I have always shied away from the complex matter of profiles, calibrating, papers and inks. It just seemed too much hassle. So much easier to upload the files to Loxley Colour in Glasgow and receive the prints a few days later.

I then did a workshop with Scott Kelby and he covered printing, calibrating, colour managed workflow etc in some detail. Scott mentioned that he used the R2880 and R3880 Epson printers and the ColorMunki calibrator. So all fired up, and feeling for the first time that I knew what I should be doing, I took the plunge and invested in the R2880 and ColorMunki.

The set up for both was quick and painless. The ColorMunki set up involves loading the drivers and software and then running the simple calibration program. While it is one of the more expensive calibrators it is superb. it allows you to calibrate your monitor and if you wish to create your own paper profiles. You simply print a test chart and then swipe each strip of colours on the paper with the calibrator and this builds a bespoke profile for your printer, ink and that particular paper combination. So far I have only used it to calibrate the monitor (and the first time you do it, it makes a huge difference) and the software prompts you to recalibrate regularly (I have it set to prompt me to recalibrate every two weeks, although this is probably overkill – it only takes a couple of minutes so it is no burden).

The drivers for the R2880 load quickly and the printer runs a set up routine when you install the ink cartridges for the first time. One cartridge has to be swapped out depending if you are printing on gloss or matte paper. I don’t understand why both can’t be fitted permanently – something for the Epson engineers to sort out.

It has quite a large footprint so you need some desk space to cope with it. But the output tray and the top paper input support fold away into the printer and seal it up to protect against dust. This also means they don’t intrude into your desk space while you are not using it.

It comes with a roll feed mechanism, so you can buy your favourite papers on the roll and print panoramas. It takes all sizes from small envelopes up to Super A3 which is bigger than A3 and is better suited to the 3:2 aspect ratio of full frame DSLR sensors. Super A3 paper is about 13 x 19 inches in size and the printer prints close to the edge. Prints at this size look stunning and are perfect for framing to hang in most homes. I bought some Hanemhule A4 paper but have hardly used any, when you have seen your prints at Super A3 you won’t want to print A4 or 10 x 8!!!

I have been trialing Epsons Archival Matte paper for my colour prints (and next want to try Hannemhule (or however you spell it) 305gm PhotoRag paper. For my mono prints I have been using the stunning Ilford Gold Silk paper.

It was with trepidation that I set about printing my first image. I sharpened it with Nik softwares excellent output sharpened plugin for Lightroom. The monitor was calibrated with the ColorMunki. I had downloaded my paper profiles from the manufacturers for the R2880. I had set up Lightroom and Photoshop correctly for a colour managed workflow. It was time to press the print button.

Breath held, I waited for the paper to emerge. Grinning, I held the print up by my studio window because I could already see the reproduction of what I had on my screen was close to perfect. I had never seen prints of such quality outside of a high end gallery. Colours were faithful, prints were not too dark as they so often are when getting them back from a lab and mono prints are quite frankly, astounding. The R2880 has three black/grey cartridges and they deliver deep rich black and mono tones, especially on the Ilford paper.

I now have loads of my prints on the walls of my home and studio, gradually replacing the substandard prints from various labs that have been up for a while. I have also been printing for customers, their own images, as it is virtually impossible to get labs to print on anything but standard papers.

The K3 inks are as good as everyone says. They are expensive, although my local supplier delivers for free next day and charges around £7.80 per colour. With nine colours, it is not cheap, but the results are worth it. The printer monitors levels and warns you when a cartridge needs replacing, which is just a one minute job. I have always sent my empty HP cartridges off to charities for recycling but they won’t accept the Epson cartridges, although a student on one of my workshops tells me you can order envelopes from Epson themselves to send empty cartridges back to them for recycling (but no charities benefit from this which is unacceptable in my mind).

At £449.99 from Amazon (which is the best price I could find from a reputable supplier and I get free next day delivery) it is not cheap, but it is well engineered and produces results worth the cost. I am already lusting after the R3880. So I am now able to wholeheartedly recommend the R2880 and the ColourMunki.